Applied-motion ST10-C-CE Instrukcja Użytkownika Strona 38
- Strona / 101
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
38
920-0025 Rev K
3/5/2015
CANopen User Manual
Manufacturer Specic Objects
The objects described in this section are manufacturer-specic to congure or monitor the
AMP CANopen driver.
0x2014~0x2017 PDOx_transmit_mask
The “TPDO detects COS” (means “on change data”) transmit event for PDOs can be
mask off by these indexs. By default, all data in a PDO is considered when checking for
change.
Each Index has 2 sub-indexes, sub-index 1 is used to mask (or reveal) bits in the lower
32bits (4bytes) of data. Sub-index 2 is the same for the upper 32bits.
Object Type Sub Number Data Type Access Type
PDO
Mapping
COS Default value
Array 3 UNSIGNED32 rw no no 0
Subindex Name Default value
00 max sub-index 2
01 PDOx_mask_LowerBytes 0xFFFFFFFF
02 PDOx_mask_upperBytes 0xFFFFFFFF
PDOx_mask_LowerBytes
bit0-31: mask off the lower 4 bytes of a TPDO when the data is “on change”
PDOx_mask_upperBytes
bit0-31: mask off the upper 4 bytes of a TPDO when the data is “on change”
0x2100 Error status bits
Error Status Bits indicates error conditions inside stack or inside application.
Object Type Data Type
Access
Type
PDO
Mapping
COS Default value
Var OCTET_STRING ro optional no 00 00 00 00 00 00 00 00 00 00
Default error status bits are:
Communication or protocol errors from driver (informative):
00 - ERROR_NO_ERROR - Error Reset or No Error.
01 - ERROR_CAN_BUS_WARNING - CAN bus warning.
02 - ERROR_RXMSG_WRONG_LENGTH - Wrong data length of received CAN message.
03 - ERROR_RXMSG_OVERFLOW - Previous received CAN message wasn’t processed yet.
04 - ERROR_RPDO_WRONG_LENGTH - Wrong data length of received PDO.
05 - ERROR_RPDO_OVERFLOW - Previous received PDO wasn’t processed yet.
06 - ERROR_CAN_RX_BUS_PASSIVE - CAN receive bus is passive.
- Applied Motion Products 1
- CANopen Manual 1
- Introduction 2
- User Advisory: 2
- Contents 3
- List of Tables 6
- Reference Documents 8
- Commonly Used Acronyms 8
- Drive Setup 9
- CANopen BitRate & NodeID 10
- Drive Conguration 11
- Figure 4: 12
- Object Dictionary 13
- Electronic Data Sheet 14
- INTEGER16 RW Yes 16
- Table 5: CiA 402 Objects 17
- 920-0025 Rev K 18
- 3/5/2015 18
- CANopen User Manual 18
- General Purpose Registers 19
- Index (hex) Object 20
- Communication Prole 21
- COS Default value 25
- Subindex Name Default value 25
- Object Type Sub Number 30
- Manufacturer Specic Objects 38
- Device Prole 45
- 0x6041 StatusWord 46
- Mode of Operation Action 49
- Position polarity 52
- Bit number Description 56
- Appendix C - Response Codes 60
- General Mode Description 61
- Enable Prole Position Mode 61
- Set Running Parameters 61
- Starting/Stopping Motion 61
- Figure 12: Single Set-Point 62
- Enable Prole Velocity Mode 66
- Enable Drive Operation 66
- Appendix F - Homing Methods 68
- Homing Method 2 69
- Homing Method 3 69
- Homing Method 4 70
- Homing Method 5 70
- Homing Method 6 71
- Homing Method 7 71
- Homing Method 8 72
- Homing Method 9 72
- Homing Method 10 73
- Homing Method 11 73
- Homing Method 12 74
- Homing Method 13 74
- Homing Method 14 75
- Homing Methods 15 and 16 75
- Homing Method 17 76
- Homing Method 18 76
- Homing Methods 19 and 20 77
- Homing Methods 21 and 22 78
- Homing Methods 23 and 24 79
- Homing Methods 25 and 26 80
- Homing Methods 27 and 28 81
- Homing Methods 29 and 30 82
- Homing Methods 31 and 32 83
- Homing Method 33 83
- Homing Method 34 84
- Homing Method 35 84
- Enable Prole Torque Mode 85
- Starting/Stopping Torque 86
- Current Verication - Example 86
- Appendix H - Q Program Mode 88
- More Information 89
- NMT Mode NMT Control 90
- NMT Status Code 90
- (Heartbeat) 90
- PDO Access 91
- TPDO Transmission Types 92
- PDO Mapping Procedure 93
- Default PDO Mapping - Stepper 94
- Default PDO Mapping - Servo 94
- PDO COB-ID 95
- Control Word of Homing Mode 97
- Status Word of Homing Mode 97
- Control Word of Q Mode 98
- Status Word of Q Mode 98
- Appendix L – Example Programs 99
- Prole Velocity Mode 100
- Homing Mode 100
- Normal Q Mode 101
- Sync Q Mode 101
- PDO Mapping 101
- Applied Motion Products, Inc 101
Powiązane produkty i podręczniki dla Sprzęt komputerowy Applied-motion ST10-C-CE
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji